Humidity/Moisture

# Microwave-Resonator-Based Sensors: An Accurate Solution for Measuring the Water Content in Paper

August 1, 2012 By: Hinrich Römhild, WORK Microwave GmbH Sensors

### Measurement methodologies using microwave frequencies and RF resonators are considered the most accurate way to obtain measurement data for calculating the weight, moisture, or water content of a variety of materials.

Today, microwave frequencies up to 100 GHz are increasingly being used in industrial applications. When used with a special resonator that adapts to the material, one can reliably obtain electrical data that characterize the material, such as its permittivity (how the material's electrical properties react to an applied electrical field) and its permeability (a measurement of the material's ability to support a magnetic field within itself). With these data one can accurately calculate the weight, moisture, or water content of a given material. Because of the wide range of available microwave frequencies, the measurement method can be customized based on the material. Figure 1 shows the permittivity of water with respect to frequency. At frequencies <3 GHz, the permittivity of water is very high; therefore these lower frequencies are ideal for measuring water content. Alternatively, when you wish to minimize the effect of residual moisture, it is better to use a measurement frequency >3 GHz.

 Figure 1. Permittivity (εr) of water vs. frequency

Resonators are structures that naturally oscillate at specific (resonant) frequencies. Quality factor (Q factor) is a measure of the resonator's bandwidth relative to its center frequency and is calculated using Equation 1:

 Q factor = f Res loaded/(flo-flu) (1)

where:

 f Res loaded = the resonant frequency of the loaded resonator flo = the frequency beyond f Res loaded that corresponds to an amplitude 3 dB lower than that of the center frequency (see Figure 2) flu = the frequency below f Res loaded that corresponds to an amplitude 3 dB lower than that of the center frequency

When a sample material is inside of the resonator's cavity region, it affects the cavity's center frequency and Q factor. Although several resonantor designs are available, to support the different inline production installations, a material's electrical permittivity and permeability are always determined using the frequency shift between the resonant frequency of the unloaded resonator (f Res unloaded) and that of the loaded resonator (f Res loaded). The Q factor is calculated based on the frequencies from 3 dB to the magnitude at resonance. In Figure 2 these are marked as flu/flo and fuu/fuo. Measuring both the shift in resonance frequency and Q factor enables us to determine two corresponding physical qualities, e.g., weight and humidity. In many cases only one physical measurement is required, in which case it is only necessary to measure the shift in resonance frequency or the Q factor, rather than both.

 Figure 2. Resonance curve and calculation of Q factor for a loaded (yellow line) and unloaded (red line) resonator

A typical resonator measurement system using the resonant cavity method consists of a resonator cavity, a signal processing part, and software control by a computer (Figure 3).

 Figure 3. A resonator-based measurement system

Using high-precision sensors based on the microwave resonator technique, manufacturers can measure the moisture content, mass, and density of a wide range of materials as well as identify foreign particles or substances that may have come into contact with those materials. This technology has been particularly useful for determining the water content of paper during the production process. The ability to control the water and wood composition of the pulp helps to optimize the quality, production throughput, and overall manufacturing costs for paper manufacturers.

Case Study: Measuring Water Content in Paper
In paper production, if the material becomes too dry or too wet the paper must be discarded. This loss can be prevented by controlling the moisture within a production space. By using microwave resonance sensors, a paper manufacturer can stay within the ideal moisture range of roughly 4%–8%. Sensors can measure the surface conditions as well as the interior of the paper without actually coming into contact with the materials and can also be used to measure glue layers applied to paper and to monitor the drying of printing inks.

After a microwave sensor is installed, the device uses a noncontact probe that detects any solid, liquid, gaseous, and granular materials; in this example (Figure 3) it detects the presence of paper. The paper mass/pulp is transported on a mesh carrier, with a sensor installed directly underneath it, as shown in Figure 4. The resulting resonance frequency is measured with a special vectoral network analyzer configuration, as we see in Figure 5. Using digital signal processing a measurement is taken, typically at speeds of up to 10 Ksps, and then analyzed. These measurements tell the paper manufacturer the moisture content, residual moisture content, mass, density, and whether foreign particles are present. The paper manufacturer then evaluates the results to determine if any adjustments to the production process need to be made.

 Figure 4. Diagram of sensor system with one-sided resonator installation

 Figure 5. Frequency shift corresponding to the water content of the paper mass. The blue curve shows the resonator measurement with no paper (for comparison). The red curve shows the resonator measurement with paper. The peak of the red curve indicates the resonator frequency value, which in this instance is equal to f1

User Interfaces
Microwave-resonator-based sensors such as the one used in this application are compatible with a range of industry standard communication interfaces to monitor and control the sensor's functions. Due to the universal design of the sensor's data interface, communication interfaces and customized interface boards can be added to the sensor for optimal integration of the sensor into a specific environment.

The communication module of the sensor has a standard IEEE 802.3 Ethernet interface so that manufacturers can directly access a sensor's data via a connected computer. The sensor also supports an ISO 11898-compliant CAN 2.0 interface for integration within production environments containing a variety of sensors and actuators. For rough environments, the sensor includes provisions for a DIN 66258 current-loop serial interface.

Any calibration formula or measurement table can be implemented into the sensor's firmware to deliver a direct, accurate reading of the paper's water content (Figure 5). Using the previously identified frequency value of f1 from Figure 5, the water content can be traced on the calibration curve in Figure 6 to approximately C1. If C1 is above or below the optimum water content for high-quality finished paper, then the paper manufacturer can either stop or increase the water flow on the production line to ensure a consistent water content, which will ultimately produce optimum quality paper.

 Figure 6. Calibration curve to determine the relationship between the resonator frequency value and the water content

Benefits of RF Resonators
In addition to accurately measuring the fiber content of paper pulp, manufacturers employing this technology experience additional benefits. For example, the resonator technique enables manufacturers to measure samples as small as 1 mm3, with high accuracy and speeds up to 10 Ksps. The high sampling speed makes this method ideal for demanding in-line applications such as paper manufacturing. The high sensitivity of the system enables it to detect very small differences of the unloaded resonator while the probe is on, maximizing the accuracy for materials with a low water content. Repeatability is down to 0.1%.

A microwave resonator method can also be used to characterize low-loss materials and materials with a low dielectric constant, which are extremely difficult to measure using other electrical measurement techniques. Substances with a low dielectric constant include a perfect vacuum; dry air; and most pure, dry gases such as helium and nitrogen. Materials with moderate dielectric constants include ceramics, distilled water, paper, mica, polyethylene, and glass. Metal oxides, in general, have high dielectric constants.

Until recently, nuclear-based sensors have been the standard for measuring the water content of paper (Figure 7). New sensors based on RF technology eliminate the need for handling nuclear sensors, enabling manufacturers to avoid the time and costs involved in specialized training for employees in the handling of nuclear sensors. Because nuclear sensors always contain a certain amount of radioactive material, manufacturers face restrictions when distributing the equipment to certain countries and may have to apply for special approval to export the devices. RF-based sensors are unaffected by those restrictions. Nuclear-based sensors also require a stringent waste-disposal process that is heavily regulated by the government. An RF-based sensor allows manufacturers to reduce potential environmental contamination.

 Figure 7. A schematic of a nuclear sensor

Manufacturers can also use either a flow-through resonator or a one-sided resonator measurement, both of which are noncontact systems. Sensors with a flow-through resonator are usually used for measuring powders, liquids, granulates, or pellets up to a certain size; the size of the material is the main limitation for flow-through resonators. In applications such as paper production, where a piece of paper in the production line can be up to 6 m wide, such a sensor wouldn't work, in most cases, and would be extremely expensive to design and manufacture. For this application, a sensor that makes one-sided measurements is an appropriate choice. Single-sided sensors are also suitable in applications where the thickness of the material is subject to larger variations during the production process. This sensor type can be integrated into an existing system.

Conclusion
Using a sensor based on the resonator measurement technique, a paper manufacturer can determine an optimum frequency range for the resonator thus ensuring—with extreme accuracy—that the paper maintains the required low water content. This ultimately leads to improved product quality and increased productivity.

Sensors using this technique are flexible enough to maintain both low and high water constants and present a cost-effective solution, because manufacturers can employ one sensor for two purposes. The microwave resonator measurement technique also ensures the slow removal of moisture from the paper, which is essential to producing superior paper.

RF sensors based on the microwave resonator technique can also be applied in other industries, such as the food, tobacco, pharmaceutical, automotive, recycling, and chemical industries where they can be used to measure moisture, mass, and density, as well as to identify foreign particles and measure dielectric properties. Because quality assurance is so critical in any manufacturing industry, the RF sensor gives companies the peace of mind that their materials meet and exceed quality expectations, allowing them to deliver the best product to their customers.

Hinrich Römhild is a sensors and measurement senior R&D engineer for WORK Microwave GmbH in Holzkirchen, Germany. He can be reached at +49 8024-6408-25 or hinrich.roemhild@work-microwave.de.

# About the Author: Hinrich Römhild

Editor’s Picks
 Article New Sensor Technologies Accelerate Robot Evolution Article Service Robots Open New Avenues for an Automated Workforce News Matrox Indio to Add Industrial Input/Output and Communication Capabilities to PCs News Global Haptic Technology Market to Rise Beyond 16% CAGR to 2022 News Positive Airway Pressure Devices Market: 8% CAGR to 2020

 Quick Links Twitter Feed Find It Fix It Forum Tweets by @sensorsonline Sensors invites you to join the Findit-Fixit Forum, where you can get answers to your sensing questions—concerning technologies, products, methods, applications, and services--and also offer help to your fellow engineers. The Forum covers all kinds of topics, from the basics to the extraordinary. Join the discussion!